لودر کشتی سیار: ظرفیت، انواع محموله و راهنمای خریدار

Port terminals and bulk handling facilities that cannot justify the capital expenditure of fixed, rail-mounted shiploaders increasingly rely on a single piece of equipment to close the gap between stockpile and ship hold: the mobile ship loader . Self-propelled on rubber tyres or crawler tracks, repositionable between berths without civil infrastructure, and capable of loading rates from 500 to 10,000 tonnes per hour depending on configuration, mobile shiploaders have redefined the economics of bulk export terminals for grain, coal, fertiliser, cement, and mineral concentrates. This guide covers the four specification decisions that determine whether a mobile shiploader delivers its rated throughput across a 20-year operational life.

TPH

500 – 10,000

Tonnes per hour loading rate range across mobile shiploader classes

LOA

20 – 45 m

Typical boom length range for Panamax to Capesize vessel reach

MOB

2 – 4 hrs

Typical repositioning time between adjacent berths under self-propelled travel

DPT

-18 m

Maximum quay draft typically served by mobile shiploader boom geometry

How Does a Mobile Ship Loader Work?

A mobile shiploader is a self-contained bulk material handling system that receives cargo from a land-side conveyor or hopper, transfers it along an articulated boom, and discharges it into a ship hold through a telescoping chute. Every functional system within the machine exists to manage material flow, dust, spillage, and structural load simultaneously.

Receiving System

Material arrives at the loader's intake conveyor from a land-side belt conveyor, hopper, or front-end loader feed point. The receiving conveyor is fitted with a weigh-belt or impact weigher that provides real-time tonnage data for loading rate control and draft survey reconciliation. Belt width at the intake is sized to match the peak feed rate from the upstream conveying system — a mismatch here creates the bottleneck that limits terminal throughput regardless of boom capacity.

Boom Conveyor and Luffing System

The main boom carries a belt conveyor from the machine body to the discharge point above the ship hold. The boom luffs — raises and lowers — via hydraulic cylinders to match the varying hold depth as the ship loads and settles deeper in the water. Luffing angles typically range from 15° (elevated, travelling position) to -15° (depressed, loading into deep holds). Some configurations add slewing — 360° or sector rotation — allowing a single machine to reach multiple hold positions without repositioning the entire machine along the quay.

Telescoping Discharge Chute

At the boom tip, a telescoping chute extends downward into the ship hold, placing the material discharge point within 1–2 metres of the cargo surface. This short drop distance is the primary mechanism for dust suppression — eliminating the long free-fall that generates fugitive dust in open-chute designs. The chute retracts automatically as the hold fills, maintaining the target drop height throughout the loading sequence. Chute extension ranges from 3 to 12 metres depending on hold depth and vessel class.

Travel and Positioning System

Rubber-tyred mobile shiploaders travel on the quay surface under self-propelled diesel-hydraulic or electric drive, repositioning between holds or berths without crane assistance. Crawler-track configurations are used where quay surface bearing capacity is limited or where gradient travel is required. Outrigger stabilisers deploy from the machine base during loading operations, distributing the structural reaction loads across a footprint that matches the quay's allowable bearing pressure — typically 50–120 kN/m² for container and bulk quay designs.

Which Cargo Types Suit Mobile Ship Loaders?

Mobile shiploaders are designed for free-flowing bulk solids — materials that discharge by gravity from a conveyor belt and can be transported on a belt without adhesion, bridging, or excessive degradation. Cargo characteristics determine belt speed, chute geometry, dust suppression requirement, and material contact surface specification.

Cargo Type	Bulk Density (t/m³)	Key Design Requirement	Dust Class	توجه ویژه
Grain (wheat, corn, soy)	0.72 – 0.85	Food-grade belt, enclosed chute	متوسط	Phytosanitary cleaning between cargoes
زغال سنگ حرارتی	0.80 – 0.90	Fire suppression, belt earthing	بالا	Water spray mandatory on all transfer points
Cement / Clinker	1.20 – 1.50	Hardened belt covers, sealed chute	بسیار بالا	Filter unit required; cement sets if wet
Fertiliser (granular)	0.90 – 1.10	Stainless contact surfaces	متوسط	Hygroscopic — enclosed conveyor preferred
Iron Ore / Concentrates	2.00 – 2.60	Heavy-duty belt (EP500 ), reinforced chute	کم – متوسط	بالا bulk density drives belt and structure sizing
Wood Pellets / Biomass	0.55 – 0.70	ATEX-rated electrical components	بسیار بالا	Explosion risk — inert gas chute flushing required

Not Suitable For

Wet, sticky materials that adhere to belt surfaces (wet clay, filter cake below 85% solids)
Lump sizes above 350 mm — requires primary crushing before belt conveyance
Liquid or slurry cargoes — requires pump-based loading systems
Bagged or containerised goods — requires crane or ramp loading equipment

Best Performing Cargoes

Dry granular materials with bulk density 0.7–1.5 t/m³ at moisture below 12%
Free-flowing materials with angle of repose below 40°
Materials with lump top size below 150 mm for standard belt configurations
Homogeneous cargoes requiring consistent grade across the load — grain, coal, fertiliser

What Loading Capacity Is Needed?

Required loading capacity is not determined by the shiploader alone — it is calculated backwards from the vessel turnaround time target, the demurrage cost per hour, and the upstream stockpile feed rate. Undersizing loading capacity costs more in vessel demurrage than the capital cost difference between machine classes over a five-year operating period.

Class I — Coastal / Small Bulk

500 – 1,500 TPH

Handysize vessels (10,000–35,000 DWT). Boom length 20–28 m. Suited to regional grain export terminals, small coal ports, and mineral concentrate facilities with annual throughput below 2 million tonnes.

Class II — Medium Bulk

1,500 – 3,500 TPH

Supramax to Panamax vessels (35,000–80,000 DWT). Boom length 28–36 m. The most common class for new greenfield bulk terminals. Covers 80% of global dry bulk vessel calls by volume.

Class III — Large Bulk

3,500 – 6,000 TPH

Post-Panamax to Capesize vessels (80,000–180,000 DWT). Boom length 36–42 m. Standard for major coal export terminals, iron ore facilities, and large grain export ports with annual volumes above 10 million tonnes.

Class IV — Ultra-Bulk

6,000 – 10,000 TPH

Capesize and VLOC vessels (180,000 DWT). Boom length 42–50 m. Dual-belt or twin-boom configurations. Required for dedicated iron ore and coal export facilities with sub-24-hour turnaround requirements on 200,000 DWT vessels.

Demurrage Calculation Rule

The industry standard for capacity sizing is: Required TPH = (Vessel DWT × Load Factor) / (Allowed Laytime in hours × Operational Efficiency). For a 75,000 DWT vessel at 95% load factor, 36-hour laytime, and 75% mechanical availability, the required nominal loading rate is 2,778 TPH — placing it squarely in Class II territory. Sizing to Class I on this vessel profile generates approximately USD 45,000 per vessel call in demurrage exposure at standard Panamax demurrage rates.

How to Choose the Right Mobile Ship Loader

انتخاب الف mobile ship loader for a new or upgraded terminal involves six specification parameters that must be resolved before approaching any equipment supplier for a formal quotation.

Quay Surface Type and Bearing Capacity

Rubber-tyred machines require a paved, load-rated quay surface with minimum bearing capacity of 80 kN/m² under outrigger pads. Crawler-track machines can operate on unpaved or lower-capacity surfaces but travel at 0.3–1.0 km/h versus 5–15 km/h for tyred machines. Confirm the quay's structural loading certificate before specifying travel system type — retrofitting outrigger pads to an under-capacity quay is a civil engineering project, not a machine accessory.

Vessel Fleet Profile

Define the design vessel — the largest vessel that will regularly call at the berth — and size the boom reach accordingly. Boom length must place the discharge chute over the outermost hold coaming at maximum vessel beam with a minimum 2 m clearance margin. Check the air draught requirement: the boom in travel position must clear the vessel's navigation bridge when transiting between holds along the berth.

Feed Conveyor Interface

The mobile shiploader's intake must interface cleanly with the terminal's land-side conveyor system. Specify the feed conveyor belt width, speed, and peak tonnage, then confirm the shiploader intake can accept this rate without spillage or belt overloading. Travelling cable reels or catenary cable systems must be sized for the full travel distance along the berth — inadequate cable management is among the most common causes of unplanned downtime on mobile shiploaders in the first year of operation.

Dust Suppression Standard

Specify the dust emission standard required by the port authority and environmental permit. Water spray systems (at intake, boom transfer, and chute tip) suit most coal, ore, and fertiliser applications. Enclosed conveyor and filter unit configurations are mandatory for cement, clinker, and wood pellet loading. ATEX Zone 2 electrical specification is required for biomass and some fertiliser cargoes — confirm the cargo's dust explosion class (Kst value) before finalising the electrical design.

Power Supply Configuration

Shore power (electric cable reel) is the standard for permanent terminal installations — lower operating cost and zero exhaust emissions at the berth. Diesel-hydraulic or diesel-electric self-contained power is specified for multi-terminal operations, remote facilities without shore power infrastructure, or applications requiring full machine independence during berth relocation. Hybrid configurations — diesel for travel, shore power for loading — optimise fuel consumption and emission compliance simultaneously.

Maintenance Access and Spare Parts Logistics

Specify the machine's preventive maintenance cycle — 250-hour, 500-hour, and annual service intervals — and confirm that the supplier maintains a regional spare parts depot within 48-hour delivery distance of the terminal. Key wear items (belt scrapers, chute liners, belt idlers, hydraulic seals) must be available locally, not on 8–12 week sea freight lead times from the manufacturer's country of origin. Request the spare parts list and local distributor network confirmation before contract award.